The 10 commandments for a good autogas installation

The 10 commandments for a good autogas installation from www.gascontrol.it

	WRONG	CORRECT
1	DO NOT place the ECU near direct heat sources and far from the possibility of air exchange	Always place the ECU in a location that can be easily reached by the outside air coming through the radiator, preferably close to the battery, on the outer side of the engine compartment
2	DO NOT place the control unit with the connector upwards as the condensation would not find a way out	Place the ECU vertically with the connector downward, to facilitate the outflow of any condensate. If it's not possible to use the position just suggested, opt for the horizontal position
3	DO NOT place the Reducer higher than the radiator, because any air present in the pipes would stop in the Reducer preventing the circulation of the water, with the risk of freezing and damaging the membranes	Place the Reducer below the top of the radiator, so that any air present in the pipes can be purged normally
4	NEVER place the Reducer in a way that the hose of the MAP engine Vacuum is too long otherwise, in case of rapid acceleration, the reaction of the Reducer's membrane will become slow, out of sync, with poor performance	Try to keep the TOTAL length of the Vacuum hoses (Reducer pipe + Pressure Sensor pipe) always less than 60 cm! Should this be impossible, consider the possibility of using a copper pipe with just two small rubber ends
5	The two pipes of the Reducer's Vacuum and of the Pressure Sensor must NOT be connected at different points, as the measured pressure may be different, with the risk of possible changing over to Petrol mode even when the Gas tank is still full	The depression for the Reducer and for the Pressure Sensor has to be taken from the same point of the collector, by a T joint
6	DO NOT place the Injectors tilted, with the coil downward, because any residual in the Gas, especially if LPG, can stagnate, hardening and blocking the movement of the shutter or restricting its hike	Place the Injectors preferably upright or, if absolutely necessary, tilted so that the residues of the Gas can flow into the engine, without stagnate in the shutter head. Try to keep the length of the pipes always less than 10 cm!
7	DO NOT use pipes of too much different lengths or it will generate an asymmetrical injection which could cause instability	The best solution is to split the Injectors in 2 pairs. Alternatively, a compromise solution consists in lengthening the two central pipes, inverting them if necessary, but in the latter case the electrical connectors (only for the Gas Injectors) must also be reversed!
8	DO NOT feed 2 groups of Injectors starting from the extremity, because the last Injector would receive a quantity of Gas by far lower than the first Injector, especially under load	Always feed 2 groups of Injectors from the center, for a more uniform distribution of the Gas
9	DO NOT install the nozzles of the Injectors too distantfrom the Petrol Injectors, because the excessive distance not only creates a delay in the Gas flow time, but it accentuates the Gas suction phenomenon from a cylinder by the adjacent cylinder; and sometimes anticipating the injection time electronically doesn't completely solve this mechanical defect	The best solution is to not exceed the maximum distance of 5 cm. If this is not possible, a compromise solution is to use a Copper or Teflon pipe for bringing the injection point to the valves
10	An old or dirty spark, which in Petrol mode does not give any problems, may cause misfirings only when running on Gas	The poor efficiency of all components subject to wear is the most common cause of issues of a Gas installation, sometimes not found in Petrol mode, like sparks and coils

7th Mar 2017 LPG Shop

Refillable and standard LPG propane gas cylinder bottle difference

What is the difference between standard and refillable gas cylinder? As you can see on the video …

29th Oct 2018 LPG Shop

AC STAG Injectors configuration options and accessories

Some gas installers are considered as an artist of LPG conversions, such masters look for perfection …

2nd Oct 2018 LPG Shop

We are improving for you... brand new website is now live!

Dear customers, partners, friends of LPG Shopwe're excited to announce that after years of constant …

30th Aug 2018 LPG Shop

The 10 commandments for a good autogas installation from www.gascontrol.it

1

DO NOT place the ECU near direct heat sources and far from the possibility of air exchange

Always place the ECU in a location that can be easily reached by the outside air coming through the radiator, preferably close to the battery, on the outer side of the engine compartment

2

DO NOT place the control unit with the connector upwards as the condensation would not find a way out

Place the ECU vertically with the connector downward, to facilitate the outflow of any condensate. If it's not possible to use the position just suggested, opt for the horizontal position

3

DO NOT place the Reducer higher than the radiator, because any air present in the pipes would stop in the Reducer preventing the circulation of the water, with the risk of freezing and damaging the membranes

Place the Reducer below the top of the radiator, so that any air present in the pipes can be purged normally

4

NEVER place the Reducer in a way that the hose of the MAP engine Vacuum is too long otherwise, in case of rapid acceleration, the reaction of the Reducer's membrane will become slow, out of sync, with poor performance

Try to keep the TOTAL length of the Vacuum hoses (Reducer pipe + Pressure Sensor pipe) always less than 60 cm! Should this be impossible, consider the possibility of using a copper pipe with just two small rubber ends

5

The two pipes of the Reducer's Vacuum and of the Pressure Sensor must NOT be connected at different points, as the measured pressure may be different, with the risk of possible changing over to Petrol mode even when the Gas tank is still full

The depression for the Reducer and for the Pressure Sensor has to be taken from the same point of the collector, by a T joint

6

DO NOT place the Injectors tilted, with the coil downward, because any residual in the Gas, especially if LPG, can stagnate, hardening and blocking the movement of the shutter or restricting its hike

Place the Injectors preferably upright or, if absolutely necessary, tilted so that the residues of the Gas can flow into the engine, without stagnate in the shutter head. Try to keep the length of the pipes always less than 10 cm!

7

DO NOT use pipes of too much different lengths or it will generate an asymmetrical injection which could cause instability

The best solution is to split the Injectors in 2 pairs. Alternatively, a compromise solution consists in lengthening the two central pipes, inverting them if necessary, but in the latter case the electrical connectors (only for the Gas Injectors) must also be reversed!

8

DO NOT feed 2 groups of Injectors starting from the extremity, because the last Injector would receive a quantity of Gas by far lower than the first Injector, especially under load

Always feed 2 groups of Injectors from the center, for a more uniform distribution of the Gas

9

The best solution is to not exceed the maximum distance of 5 cm. If this is not possible, a compromise solution is to use a Copper or Teflon pipe for bringing the injection point to the valves

10

An old or dirty spark, which in Petrol mode does not give any problems, may cause misfirings only when running on Gas

The poor efficiency of all components subject to wear is the most common cause of issues of a Gas installation, sometimes not found in Petrol mode, like sparks and coils

Recent Posts